EXPERIMENTAL STUDY OF FILTER CAKE FORMATION ON DIFFERENT FILTER MEDIA

Authors

  • M. Saleem Institute of Chemical Engineering & Technology, University of the Punjab, Lahore, Pakistan
  • M. S. Tahir Department of Chemical Engineering and Environmental Technology, Graz University of Technology, Graz , Austria
  • G. Krammar Department of Energy and Process Engineering, NTNU, Trondheim, Norway

Abstract

Removal of particulate matter from gases generated in the process industry is important for product recovery as well as emission control. Dynamics of filtration plant depend on operating conditions. The models, that predict filter plant behaviour, involve empirical resistance parameters which are usually derived from limited experimental data and are characteristics of the filter media and filter cake (dust deposited on filter medium). Filter cake characteristics are affected by the nature of filter media, process parameters and mode of filter regeneration. Removal of dust particles from air is studied in a pilot scale jet pulsed bag filter facility resembling closely to the industrial filters. Limestone dust and ambient air are used in this study with two widely different filter media. All important parameters like pressure drop, gas flow rate, dust settling, are recorded continuously at 1s interval. The data is processed for estimation of the resistance parameters. The pressure drop rise on test filter media is compared. Results reveal that the surface of filter media has an influence on pressure drop rise (concave pressure drop rise). Similar effect is produced by partially jet pulsed filter surface. Filter behaviour is also simulated using estimated parameters and a simplified model and compared with the experimental results. Distribution of cake area load is therefore an important aspect of jet pulse cleaned bag filter modeling. Mean specific cake resistance remains nearly constant on thoroughly jet pulse cleaned membrane coated filter bags. However, the trend can not be confirmed without independent cake height and density measurements. Thus the results reveal the importance of independent measurements of cake resistance.

References

A. Dittler, B. Gutman, R. Lichtenberger, H.

Weber and G. Kasper, Powder Technology

, No. 2 (1998) 177.

H. Leubner and U. Riebel, Chem. Engg.

Tech. 27, No. 6 (2004) 652.

F. Loeffler, H. Dietrich and W. Flatt, Dust

Collection With Bag and Envelop Filters,

Fried Vieweg and Sons, Braunschweig,

Germany (1988).

W. Hoeflinger, G. Mauschitz and W.

Koschutnig, Cleaning Behaviour of Textile

Filter Media, European Conference on

Filtration and Separation, Gotenburg, June

-26 (2002).

K.T. Hindy, J. Sievert and F. Loeffler,

Environment International, 13, No. 2 (1987)

C.C. Chen, W. Y. Chen, S.H. Huang, Y. Lin

W, Y.M. Kuo and F.T. Jeng, Aerosol Science

and Technology 34 (2001) 262.

M. Saleem, G. Krammer, M. R¨uther and H.

Bischof, Optical Measurement of Cake

Thickness Distribution and Cake Detachment

on Patchily Cleaned Commercial Bag Filters.

In Proceedings of the International

Conference and Exhibition for Filtration and

separation Technology, Volume II, pages

–58, Wiesbaden, Germany, October 2005.

FILTECH Exhibitions, Germany.

M. Saleem and G. Krammer, Powder

Technology 173 (2007) 93.

E. Schmidt, Filtration and Separation, 32, No.

(September 1995) 789–793.

D. H. Smith, V. Powell, G. Ahmadi and E.

Ibrahim, Powder Technology 94 (1997) 15.

A. Kavouras and G. Krammer, Powder

Technology 133 (2003) 134.

E. Schmidt, Elektrische Beeinflussung der

Partikelabscheidung in Oberflaechenfiltern.

PhD thesis, Faculty of Chemical Engineering,

Karlsruhe University of Technology,

Karlsruhe, Germany (1991).

Downloads

Published

29-06-2020

How to Cite

[1]
M. Saleem, M. S. Tahir, and G. Krammar, “EXPERIMENTAL STUDY OF FILTER CAKE FORMATION ON DIFFERENT FILTER MEDIA”, The Nucleus, vol. 46, no. 3, pp. 83–89, Jun. 2020.

Issue

Section

Articles

Most read articles by the same author(s)