A Modified Model of Axial Flux Permanent Magnet Generator for Wind Turbine Applications
Abstract
The Axial Flux Permanent Magnet Generators (AFPMGs) are gaining immense attention in the modern era. The single stage AFPMG topology consists of one stator disc which is held stationery between two revolving rotor discs attached with a common shaft. The number of poles of AFPMG depends on the winding pattern in which the coils are connected in series within stator disc. Connecting the coils in begin-to-end winding pattern, doubles the number of poles which also increases the active mass of AFPMG. The AFPMG considering begin-to-end winding pattern, can be operated at half shaft speed. This AFPMG is also having greater air gap flux density which, ultimately, improves the power density parameter of AFPMG. In this paper, a modified AFPMG has been proposed which is designed by considering begin-to-end winding pattern. A 380W single phase, single stage prototype model has been developed and tested. The test results show that power density of designed AFPMG with begin-to-end winding pattern has been improved by 32% as compared to AFPMG with begin-to-begin winding pattern. The proposed low speed and high power density AFPMG model can be actively deployed for wind turbine applications.References
M.M. Ashraf, T.N. Malik and M. Iqbal, Journal of Renewable
and Sustainable Energy 6 (2014) 013110.
M.M. Ashraf, T.N. Malik and M. Iqbal, The Nucleus 51 (2014)
A. Jarral, M. Ali, M.H. Sahir and R.A. Pasha, The Nucleus 50
(2013) 7.
M.M. Ashraf, T.N. Malik, S. Zafar and U.N. Raja, The Nucleus
(2013) 173.
S. Ekram, Proc. Int. Conf. on Electrical Machines and Systems,
Tokyo, 15-18 Nov. (2009) pp. 1-5.
P. Wannakarn, T. Tanmaneeprasert, N. Rugthaicharoencheep
and S. Nedphograw, Proc. 4th International Conference on
Electric Utility Deregulation and Restructuring and Power
Technologies, Weihai, Shandong, 6-9 July (2011) pp. 763-766.
M. Aydin, S. Huang and T. Lipo, Wisconsin Electric Machines
& Power Electronics Consortium, University of WisconsinMadison, Madison, WI (2004) 1691.
J. Zhao, D. Cheng, P. Zheng, X. Liu, C. Tong, Z. Song and
L. Zhang, J. Appl. Phy. 111 (2012) 07A719.
M. Topor, Y.-D. Chun, D.-H. Koo, P.-W. Han, B.-C. Woo and
I. Boldea, J. Appl. Phy. 103 (2008) 07F127.
J.F. Gieras, R.-J. Wang, and M.J. Kamper, Axial Flux
Permanent Magnet Brushless Machines, Springer (2008).
S. Javadi, M. Mirsalim, and M. Mirzaei, Proc. Int. Conf. on
Electrical Machines and Systems (ICEMS), Beijing, 20-23 Aug.
(2011) pp. 1-4.
W. Weimin, K.W.E. Cheng, K. Ding, and L.C. Meng, IEEE
Transactions on Magnetics 47, 10 (2011) 2391.
T.A.C. Maia, O.A. Faria, A.A.R.F.E. Cardoso, F.S. Borges,
H.G. Mendonca, M.A. Silva, J.A. Vasconcelos, S.R. Silva, and
B.M. Lopes, Procd. International Conference on Electrical
Machines and Systems (ICEMS) 20-23 Aug. 2011, Beijing, p.
-6.
B. Xia, M.J. Jin, J.X. Shen, and A.G. Zhang, Procd. IEEE
International Conference on Sustainable Energy Technologies
(ICSET), Kandy, 6-9 Dec. (2010) pp. 1-5.
R.K. Agarwal, Principles of Electrical Machine Design, Dewan
Sanjeev Kumar Kataria, Delhi (2000) pp. 600.
S.J. Chapman, Electric Machinery Fundamentals, McGrawHill, New York (2005).
L. Mingyao, H. Li, L. Xin, Z. Xuming, and Z.Q. Zhu, IEEE
Transactions on Magnetics 47 (2011) 4457.
S. Huang and G. Xie, Journal of Shanghai University (English
Edition) 1 (1997) 232.